Monday, July 27, 2009

Sucess is Bittersweet

Last night after ordering the Omega amplifier, I went to go put away all my electronics gear. Just for kicks, I thought I'd try to get the LM339 based circuit to work one more time. An Eddisonian inspiration led me to try grounding one of the magnetic pickup lines at the amplifier, and wouldn't you know it, the noise problems went away.

So, the circuit below seems to work perfectly in my application. To recap, I have the following

- A Cox AN8-4 turbine flow meter
- A magnetic pickup which outputs a 10 mV minimum peak to peak signal
- A Measurement Computing 1208FS



I'm sure that it never would have worked had I not bought the Omega unit.

Sunday, July 26, 2009

Make vs. Buy

I recently bought a nice turbine flow meter off Ebay. I was planning to use the counter on my DAQ board to measure the frequency of the turbine and convert frequency into flow. Unfortunately, the flow meter magnetic pickup turns out to have a millivolt peak to peak output and the counter expects a TTL (0-5V) signal.

So, says me, "Self, how hard can it be to cobble together some Radio Shack parts to fix this problem ..." After a little bit of work and a trip to the store, I ended up with a circuit that sort of works, based on a LM339 comparator IC. The schematic is below.

Now, this particular setup has a couple of features.
1) When the turbine is not spinning, the DAQ counter reads 60 Hz. This is actually not an issue, because 60 Hz is below the low limit of the turbine. I simply have to remember that if the DAQ board says the flow rate is 0.125 gal/min, its actually zero.

2) If i touch any part of the circuit between the DAQ card and up to and including the body of the meter itself, the DAQ counter reads about 20 kHz. This IS a problem, as the max frequency of the meter is about 1800 Hz. However, its not clear to me if this would be an issue in operation. I seem to remember something about grounding problems causing these kinds of issues....

Now for the point of the post. Omega sells a nifty little box that is designed to do exactly what I need in this case. It costs $70. So, should I have just bought one instead of futzing around with making my own? I mean, $70 is a pretty nice dinner for me and the Mrs. So far, I have about 3 hours into this tiny project. Call it 4 hours by the time i transfer the project from the bread board to a perf board and come up with some sort of enclosure. So, is the value of my time less or more than $17.50/hour?

Friday, June 26, 2009

And here it is ...


Tonight, I drilled the injector holes and welded up the motor. The injector holes were surprisingly simple to drill at 0.06", 0.022" and 0.013". I did find that the middle sized drill bits were only good for about 6 holes in the stainless.

With the exception of the spark plug bung, I'm very happy with how it turned out. Welding is definately simpler than trying to design, fab, and assemble a bolted joint.




Sunday, June 21, 2009

Its like watching paint dry ...


Well, the good news is my day job has slowed down a little ... bad news is that I still haven't made any fire and smoke :(

After running through multiple repair cycles on the injector head, I finally gave up about two weeks ago and started building another injector. The one I have was designed to be bolted on to the chamber. I used that design because I didn't have a welder and I thought it would be nice to be able to remove the head and swap it out. Since I now have a welder and have been practicing with stainless steel, I've since come to the conclusion that welding is a MUCH simpler way to go (which is the advice that John Carmack gave a while back). If you do end up swapping injectors, its really not a big deal at all to cut the old one off and weld the new one on.

The new design also moves the spark plug off of the injector itself and onto the chamber. This was done to free up the space and make the injector much simpler to machine.

While I don't quite hate stainless as much as Paul Breed, I do find that it is much less forgiving than other materials. The main thing is to simply be patient - use the recommended cutting speeds and feed rates which are an order of magnitude less than aluminum. On the plus side, it is showing me some bad machining habits that I didn't know I had.

Below is a picture of the part I finished today, the cover for the fuel manifold on the injector. Also in my hand are two ruined 1/8" cobalt end mills. One I simply broke from over-feeding (feeding to fast/too much force). The other one I literally cooked from over-heating. It still cuts, but it more closely resembles a ball-end mill :)